How to Use Thread Ring Gages

Go and no go thread ring gages are very easy to use. The user must first select the correct size thread ring gages for the corresponding external threaded product. This is obviously critical but sometimes difficult as drawings and specification requirements are frequently missing, incomplete, or incorrect. The user of the ring gages should ensure that the correct major diameter, TPI/pitch, Class of fit, and any special pitch diameters are clearly specified. The user should also confirm that the gages conform to the proper national or international standard. In the USA it is commonly assumed that metric thread gages conform to the ANSI/ASME B1.16M but this may not be the case particularly when working with an international customer or a globally recognized company with manufacturing facilities located in the USA and engineering located in Asia or Europe. Other metric standards like ISO or JIS may be required. It is also important to confirm that pitch diameters on the gages match the part specification. For example, a part gaged prior to plating will have special pitch diameters. The ring gages selected should be engineered and made correctly to the preplate or before plate pitch diameters. The ring gauges should be marked with B/P or P/P designation for quick and easy identification. Finally, the inspector should confirm the gages are calibrated. It is always advisable to recheck the thread ring gages prior to use with the matching set plug regardless of the calibration sticker’s current status. Many companies arbitrarily select annual frequencies of calibration rather than basing frequency on usage. This can be dangerous as thread ring gauges can be worn out of tolerance or damaged during the course of a production run. The best thread ring gaging practice utilizes several sets of thread ring gages all set to a matching master set plug gage. One or two sets can be used for in process inspection while another set can be used for final inspection and a master set retained for dispute in the event that gages fail to correlate.

Adjustable American Gage Design - AGD thread ring gauges are designed with radial slots which form natural dirt grooves that tend to clean the threads of the work piece. It is important to note that thread ring gages are not work dies. It is advisable to clean the work piece prior to gauging as this will extend the wear life of the ring gauges. They should be cleaned with solvent or air and then frequently recoated with a rust preventative/gage preservative. Thread ring gauges should be laid flat to prevent them from rolling off a table. All gauging whenever possible should be done over an inspection table in the event that the gage is accidentally dropped. If a gage is dropped it should be immediately re-inspected with a matching set plug. Any impact to the thread ring gages may result in a change to its size.

The go thread ring gage should engage the externally threaded part with very little force used. The engagement should be smooth. There is no specification regarding torque or pounds of pressure for using thread ring gauges. Common sense should be applied based on factors of thread size, pitch, and application. If the gage starts to bind, the inspector should stop before damaging the part or the gage.  The part may be oversized or tapered. Other possibilities include lead error or a damaged thread. An inspector can evaluate the critical elements of the threaded part by inspecting the major diameter using a measuring instrument such as a micrometer. Pitch diameter may be checked by using a 3-wire method. Lead, angle and minor diameter can be checked with an optical comparator or vision system. With fine threads the inspector should be careful to not cross thread the parts.

It is important to use the no go gage as it checks pitch diameter exclusively. It is unaffected by other conditions in the screw thread as it is intentionally truncated on the crests and with greater clearance applied on the roots of the thread. The no go thread ring should not turn on the part more than 3 turns although in practice it is advisable to limit the amount of turns to 1 ½ - 2 turns max. The user just simply counts turns. The end user should review the applicable thread specification in detail as there are variations to the above practice. /no-go-gaging-per-ansi-asme-b1.2-1983-an-american-national-standard/technicalinfo/.

Thread Check Inc.
info@threadcheck.com
www.threadcheck.com
631-231-1515

By clicking "I Agree", you agree to our Terms and that you have read our Data Use Policy.